Top 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Don't take too lightly the forklift at work. If the operation is not good, there will be severe accidents in minutes, and there are many accidents involving forklifts.

Situation 1: The forklift cargo blocked the motorist's sight, and the person in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Case 3: The width of the forklift cargo goes beyond the allowed size of the path and hangs on the roadside rack, which virtually creates an mishap.
Situation 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the personnel illegally, the forklift vehicle driver does not wear the seat belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure must take note of these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety and security of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale need to be safe prior to starting.
3. When the forklift starts with a lots, the motorist should initially confirm that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges in the sky. When the tons is taking a trip, the fork must not be increased expensive, which will impact the security of the forklift. .
3. After dumping, the fork should be reduced to the regular driving position before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the automobile to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and should keep a specific security distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The tons shall not be raised except when piling or filling. .
8. The elevation of the lots have to not obstruct the motorist's sight. In special situations, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold items and play a balancing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely manner, and they will certainly never run with ailments or conceal them.

filling and discharging.
1. When fork-loading items, the range between the two forks need to be readjusted as required to make the lots of both forks balanced and not manipulated, and one side of the product ought to protest the shelf. .
2. It is forbidden to collaborate with a solitary fork or use a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle need to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch various other products or items. The tons needs to be stabilized with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted forward somewhat when the lots is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and Stand-on Electric Pallet Stacker ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to participate in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to use the brake inertia to slip, put, round or roll objects. .
10. It is not enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for unique conditions, such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating Stand-on Electric Pallet Stacker oil and air conditioning water need to be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are normal.
5. After the forklift is running, the external leak needs to likewise be inspected and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the car;.
2. When you run into somebody in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free turning";.
6. Adding and down the slope must be slow and consistent, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is above 10%, the vehicle must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move forward, if they encounter huge or heavy products and go to the motorist's line of sight, they must take the turning around exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not allowed to lift the goods for far away driving.
3. It is not permitted to pick up the goods by passing on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not allowed to bring individuals to work with the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below problems.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844